Beckhoff CX210000x4 Uživatelský manuál stáhnout pdf (Strana 40)

Errorhandlinganddiagnostics

5.3 LEDsofthepowersupplyunit(CX21000xx4)inEbus

mode

Afterswitchingon,thepowersupplyimmediatelycheckstheconnectedBusTerminalconfiguration.IfKbus

terminalsaredetected,theerrorfreebootupissignaledbythered“I/OERRLED”goingout.Ifthe“I/OERR”

LEDblinks,anerrorintheareaoftheterminalsisindicated.Theerrorcodecanbedeterminedfromthe

frequencyandnumberofblinks.Thispermitsrapidrectificationoftheerror.

Display LED Meaning

Us24V PowersupplyfortheCPUmodule.TheLEDlights

greenifthepowersupplyiscorrect.

Up24V Powersupplyforterminalbus.TheLEDlightsgreenif

thepowersupplyiscorrect.

L/A off Ebusnotconnected

on Ebusconnected/nodatatraffic

flashing Ebusconnected/datatrafficontheEbus.

5.4 Faults

PleasealsorefertotheSafetyinstructionssection.

Possiblefaultsandtheircorrection

Fault Cause Measures

nofunctionaftertheEmbeddedPC

hasbeenswitchedon

nopowersupplyfortheEmbedded

PC

othercauses

1.Checkthefuse

2.Measurevoltageatconnection,

checkplugwiring,callBeckhoff

support

EmbeddedPCdoesnotbootfully Harddiskdamaged(e.g.dueto

switchingoffwhilesoftwareis

running),incorrectsetup,other

causes

ChecksetupCallBeckhoffSupport

Computerboots,softwarestarts,

butcontroldoesnotoperate

correctly

Causeofthefaultiseitherinthe

softwareorinpartsoftheplant

outsidetheEmbeddedPC

Callthemanufacturerofthe

machineorthesoftware.

CFcardaccesserror FaultyCFastcard,faultyCFastslot UseadifferentCFastcardtocheck

theCFastslotCallBeckhoff

Support

EmbeddedPConlyworkspartially

ortemporarily

Defectivecomponentsinthe

EmbeddedPC

CallBeckhoffsupport

PleasemakeanoteofthefollowinginformationbeforecontactingBeckhoffserviceorsupport:

1. PrecisedeviceID:CXxxxxxxxx

2. Serialnumber

3. Hardwareversion

4. Anyinterfaces(N030,N031,B110,...)

5. TwinCATversionused

6. Anycomponents/softwareused

Thequickestresponsewillcomefromsupport/serviceinyourcountry.Thereforepleasecontactyour

regionalcontact.Fordetailspleaserefertoourwebsiteatwww.beckhoff.deoraskyourdistributionpartner.

CX210000x440 Version1.0

1 2 ... 35 36 37 38 39 40 41 42 43 44 45

Komentáře k této Příručce

Žádné komentáře

Beckhoff CX2100­00x4 Uživatelský manuál Strana 40

Komentáře k této Příručce

Související produkty a manuály pro Počítače Beckhoff CX2100­00x4

Beckhoff CX210000x4 Uživatelský manuál Strana 40

Související produkty a manuály pro Počítače Beckhoff CX210000x4